5575 Magnatron Blvd Suite I San Diego, CA 92111 | License #789831
E-mail us: info@foxplumbing.com
Support: 24/7
Follow us:
Page Title BG

How Often Should You Flush Your Water Heater in San Diego?

Last updated: November 2026

Most tank water heaters need flushing at least once a year, and Rheem recommends every six months where water is hard. The City of San Diego's 2024 water quality report lists average hardness of 216 to 230 parts per million at its three treatment plants, which the USGS calls very hard. So a six-month schedule fits many San Diego homes.

The schedules below apply to gas and electric tank water heaters. Tankless units get descaled instead, which is covered further down. If your water comes from a district other than the City of San Diego, check that district's own annual water quality report, because hardness varies by source.

How often should you flush a tank water heater?

A tank water heater should be flushed about once a year under normal conditions and about every six months in hard water, according to Rheem. A. O. Smith gives similar guidance: most water heaters should be flushed at least once a year, and homes in hard water areas may need to flush more often. Your owner's manual has the final say for your model.

Rheem also says the right schedule depends on your water quality and how much hot water your household uses. A big family running showers, laundry and the dishwasher every day pushes more water, and more minerals, through the tank than a single person who is gone all day. Visible sediment is another reason Rheem gives for flushing more often.

Your situationSuggested scheduleSource
Tank heater, average waterOnce a yearRheem; A. O. Smith ("at least once a year")
Tank heater, hard water (City of San Diego water qualifies)About every six monthsRheem
Heavy hot water use or visible sedimentMore often than the base scheduleRheem
Tankless heaterDescale about once a year, more often with hard waterRheem
Tank 8 to 12 years old or olderHave a plumber look before any DIY flushRheem

If you are on City of San Diego water and nobody has drained your tank in the past year, you are probably behind. Put the next flush on the calendar now and set a reminder for six months after that.

Why does San Diego's hard water build up sediment in a water heater?

Sediment in a water heater is the layer of minerals that separates from the water and settles at the bottom of the tank, as Rheem describes it. Hard water carries more of those minerals. The U.S. Geological Survey explains that when hard water is heated, as it is in a home water heater, solid deposits of calcium carbonate can form.

The numbers for San Diego are high. In the City of San Diego Public Utilities Department's 2024 annual drinking water quality report, average total hardness was 216 parts per million at the Alvarado plant, 229 at Miramar and 230 at Otay. That works out to about 12.6 to 13.4 grains per gallon. Water the city buys already treated averaged 155 parts per million.

The USGS hardness scale classes 121 to 180 milligrams per liter as hard and anything above 180 as very hard. So the city's own plants deliver very hard water, and even the purchased water lands in the hard range.

In the tank, that means more sediment. Rheem says built-up sediment acts like insulation at the bottom of the tank, so the heater runs longer heating cycles to reach temperature. The USGS adds that hard-water scale can reduce the life of equipment, raise the cost of heating water and lower the efficiency of electric water heaters.

Some homeowners treat the water itself. If you have a softener or are thinking about one, read up on whether a water softener can hurt your water heater before you change your maintenance routine.

What are the signs your water heater needs flushing now?

A water heater that rumbles or pops, runs out of hot water sooner than it used to, or takes longer to recover between showers often has sediment built up in the tank. Rheem lists those signs, plus rusty or cloudy hot water and energy bills that climb without any change in how much hot water you use.

The noise is the easiest one to notice. Rheem says rumbling and popping are often caused by sediment buildup that flushing can remove.

Cloudy or rust-tinted hot water is on Rheem's list too. A. O. Smith notes that mineral buildup raises the risk of leaks, bad smells and other common water heater problems.

One sign is not a flushing problem. If you see water pooling around the base of the tank, stop and read what to do if your water heater is leaking. A leak calls for a different plan than routine maintenance.

Can you flush a water heater yourself?

Many homeowners can flush a tank water heater themselves if they follow the owner's manual and take the safety steps seriously. The water coming out is hot, and the heater must stay off while the tank is empty. The U.S. Department of Energy's Building America Solution Center warns that a heater that turns on while empty or partly empty can be damaged quickly.

The Building America Solution Center guide and A. O. Smith's instructions describe the same basic process.

  1. Read your owner's manual first, since steps vary by model and fuel type.
  2. Turn off the power or gas to the heater, then close the cold water supply valve. On a gas unit, follow the manufacturer's instructions so you do not accidentally put out the pilot light in a way that could let gas leak.
  3. Open a hot water faucet in the house so air can enter as the tank drains.
  4. Connect a garden hose to the drain valve and run it to a spot lower than the bottom of the tank, such as a floor drain or outside.
  5. Open the drain valve and let the tank drain. Briefly opening the cold water supply now and then stirs up sediment, and you keep flushing until the water runs clear.
  6. Close the drain valve, refill the tank with the hot faucet still open until air stops sputtering out, then restore power or gas and remove the hose.

A. O. Smith recommends thick gloves and safety goggles, and turning off the heat source ahead of time so the water can cool, which lowers the risk of scalds. The Building America guide also suggests waiting several hours before doing laundry, since the water may still be cloudy and needs time to heat.

When should a plumber handle the flush instead?

A plumber should handle the flush when the drain valve will not open or leaks, when there is heavy rust or corrosion around the fittings, when the tank is 8 to 12 years old or older, or when you are unsure about the gas or electrical parts. Those are the situations Rheem lists for calling a professional.

Go back to the flush you put on the calendar earlier. If that tank is 8 to 12 years old or older, Rheem warns that on older tanks with hardened sediment, attempting a flush yourself could lead to leaks or further damage. If the drain valve will not budge, or starts dripping once you touch it, stop there.

A. O. Smith says much the same: if you cannot flush the tank, for example because sediment has clogged the drain valve, call a plumber or service technician.

If your tank is older and has never been flushed, a new unit may be a better use of the money than upkeep on one near the end of its life. If you are weighing that, see how much it costs to replace a water heater in San Diego and ask your plumber for an honest read on the tank's condition.

Do tankless water heaters need flushing too?

Tankless water heaters need descaling instead of a tank flush, according to Rheem. Descaling clears mineral scale from the heat exchanger, the part that heats water as it passes through. Rheem recommends doing it about once a year and more often if your water is hard or high in minerals, which describes most City of San Diego water.

The job is different from draining a tank. Rheem says tasks that involve gas lines, burners or electrical components, including flushing the heat exchanger, are best left to a licensed professional.

Rheem also lists checking the pressure relief valve as part of tankless upkeep, to make sure it opens and closes properly and does not leak.

If you are still deciding which type to buy, the maintenance difference is one factor among several in our comparison of tankless vs. traditional water heaters for San Diego homes.

Frequently asked questions

Does flushing a water heater help it last longer?

It can help, though no flush guarantees a set number of extra years. The USGS says the calcium carbonate scale that forms when hard water is heated can reduce the life of equipment and raise the cost of heating water. Rheem says regular flushing reduces strain on heating elements or burners and helps prevent overheating and internal damage. Rheem also recommends checking the anode rod every year.

Is it safe to flush an old water heater that has never been flushed?

Not always. Rheem warns that on older tanks with hardened sediment, attempting a flush yourself could lead to leaks or further damage, and it lists units 8 to 12 years old or older as a reason to call a professional. A plumber can check the drain valve and the condition of the tank first, then tell you whether a flush makes sense or whether the money is better spent on a replacement.

What else should be checked when a water heater is flushed?

The anode rod and the temperature and pressure relief valve. Rheem recommends checking the anode rod yearly and replacing it if it is corroded, thinned or coated with calcium or sediment. For the relief valve, Rheem says to lift the handle briefly to make sure water flows freely through the discharge pipe. It also notes that inspecting or replacing these parts often requires tools and safety precautions and is best handled by a qualified plumber.

Will flushing my water heater lower my energy bill?

It may help if sediment has built up. Rheem explains that sediment acts like insulation at the bottom of the tank, so the heater runs longer heating cycles, and it lists rising energy bills without increased usage as a sign a flush is due. The USGS says scale from hard water can raise the cost of heating water. How much you save depends on how much sediment is in your tank, so there is no fixed savings figure to expect.

How we can help

If your water heater is rumbling, running short on hot water or has not been drained in years, a plumber can check it before you try a flush yourself. Fox Plumbing is a family-owned San Diego plumbing company with over 40 years of experience. We handle water heater repairs, water heater leaks and replacements, and tankless water heaters, so we can look at an older tank and tell you whether it is worth repairing or close to replacement. If your water heater has already started leaking, we offer fast-response emergency plumbing service. Call 619-286-6325 or contact Fox Plumbing to talk through your water heater.

Share: